中空玻璃雙組份打膠機部分毛病剖析及辦法
Analysis and measures of some defects of double glazing machine for insulating glass
中空玻璃設備中的雙組份打膠機在運用過程中，或許會由于運用不當或是其他原因形成一些毛病。那么設備在呈現毛病時咱們要假如剖析毛病原因，并采納相應的辦法呢？下面小編介紹雙組份打膠一些毛病及辦法。
During the operation of the two-component glue beater in the hollow glass equipment, there may be some defects due to improper use or other reasons. So when the equipment is defective, do we need to analyze the causes of the defects and adopt corresponding methods? The following is a brief introduction to some problems and solutions of the two components.
1.雙組份打膠機A.B組份份額不對
1. the proportion of A.B component of two component glue machine is not right.
呈現這種狀況的原因有以下幾種狀況：
The reasons for this situation are the following:
份額泵阻塞。B泵吸空。A泵或B泵有內走漏。A膠或B膠桶無料。份額泵前有空氣未排出。混合器單向閥走漏。B泵過濾器阻塞。
The share pump is blocked. B pump empty. A pump or B pump has internal leakage. A gum or B gum bucket is not available. Air is not discharged before the pump. The mixer one-way valve leaks. B pump filter blocked.

針對以上原因咱們采納以下辦法進行處理：
In view of the above reasons, we adopt the following measures to deal with:
清洗份額泵；B泵壓盤放氣閥翻開放氣；替換A泵或B泵密封圈；加料；翻開份額泵前的放氣閥放氣；.清洗或替換 混合器單向閥；清洗B泵過濾器。
Cleaning share pump; B pump pressure disc vent valve open air; Replacing A or B pump seal; Feeding; Opening share pump before the vent valve air;. Cleaning or replacing mixer one-way valve; Cleaning B pump filter.
2..當咱們?cè)谶\(yùn)用雙組份打膠機時擠膠不接連，發作這種狀況的原因有以下幾種狀況：
2. When we use a two-component glue beater, there are several reasons for this situation:
混合器未清洗潔凈.并已固化。A組份或B組份無料。膠中含有空氣。份額泵前空氣未排盡。A泵.B泵有內走漏。吸入閥閥芯內的V型密封圈未壓緊。B泵過濾器濾網阻塞。
The mixer is not cleaned and cleaned. A component or B component was not available. Glue contains air. The air is not drained before the pump. A pump.B pump has internal leakage. The V seal ring in the suction valve spool is not pressed. B filter strainer blockage.
相應的辦法如下：
The corresponding measures are as follows:
清洗混合器；加料(換桶)排盡空氣；翻開份額泵前的球閥排氣；替換密封圈；壓緊閥芯密封圈；清洗B泵過濾器。
Clean mixer; Fuel (barrel change) exhaust air; Open the ball valve before the share pump exhaust; Replace the sealing ring; Press the valve core sealing ring; Clean the B pump filter.
這兩種毛病，還有或許由于操作人員或是設備問題呈現其他毛病。

These two problems may also cause other problems due to operators or equipment problems.

本文由濟南昌盛機械http://linshi.jncsjx.com整理,對雙組份打膠機感興趣的朋友可以關注我們，我們將為您提供更多知識.
This article is compiled by Jinan Changsheng Machinery http://linshi.jncsjx.com. Friends interested in the two-component glue beater can pay attention to us, and we will provide you with more knowledge.